Details
| Original language | English |
|---|---|
| Pages (from-to) | 285-292 |
| Number of pages | 8 |
| Journal | International journal of computer assisted radiology and surgery |
| Volume | 10 |
| Issue number | 3 |
| Publication status | Published - Mar 2015 |
Abstract
Purpose: The integration of a robot into an image-guided therapy system is still a time consuming process, due to the lack of a well-accepted standard for interdevice communication. The aim of this project is to simplify this procedure by developing an open interface based on three interface classes: state control, visualisation, and sensor. A state machine on the robot control is added to the concept because the robot has its own workflow during surgical procedures, which differs from the workflow of the surgeon.
Methods: A KUKA Light Weight Robot is integrated into the medical technology environment of the Institute of Mechatronic Systems as a proof of concept. Therefore, 3D Slicer was used as visualisation and state control software. For the network communication the OpenIGTLink protocol was implemented. In order to achieve high rate control of the robot the “KUKA Sunrise. Connectivity SmartServo” package was used. An exemplary state machine providing states typically used by image-guided therapy interventions, was implemented. Two interface classes, which allow for a direct use of OpenIGTLink for robot control on the one hand and visualisation on the other hand were developed. Additionally, a 3D Slicer module was written to operate the state control.
Results: Utilising the described software concept the state machine could be operated by the 3D Slicer module with 20 Hz cycle rate and no data loss was detected during a test phase of approximately 270 s (13,640 packages). Furthermore, the current robot pose could be sent with more than 60 Hz. No influence on the performance of the state machine by the communication thread could be measured.
Conclusion: Simplified integration was achieved by using only one programming context for the implementation of the state machine, the interfaces, and the robot control. Eventually, the exemplary state machine can be easily expanded by adding new states.
Keywords
- 3D Slicer, Finite state machine, Robot control interface, Visualisation
ASJC Scopus subject areas
- Medicine(all)
- Surgery
- Engineering(all)
- Biomedical Engineering
- Medicine(all)
- Radiology Nuclear Medicine and imaging
- Computer Science(all)
- Computer Vision and Pattern Recognition
- Medicine(all)
- Health Informatics
- Computer Science(all)
- Computer Science Applications
- Computer Science(all)
- Computer Graphics and Computer-Aided Design
Cite this
- Standard
- Harvard
- Apa
- Vancouver
- BibTeX
- RIS
In: International journal of computer assisted radiology and surgery, Vol. 10, No. 3, 03.2015, p. 285-292.
Research output: Contribution to journal › Review article › Research › peer review
}
TY - JOUR
T1 - OpenIGTLink interface for state control and visualisation of a robot for image-guided therapy systems
AU - Tauscher, Sebastian
AU - Tokuda, Junichi
AU - Schreiber, Günter
AU - Neff, Thomas
AU - Hata, Nobuhiko
AU - Ortmaier, Tobias
N1 - Funding information: The authors wish to thank Gregory Fischer and Nirav Patel from the WPI for the provision of the java implementation of OpenIGTLink igtlink4j as well as the Organizers of the NAMIC 2013 Summer Project Week. This work is supported in part by the National Institute of Health (R01CA111288, P01CA067165, P41RR019703, P41EB015898, R01CA124377, R01CA138586, R42CA137886, and U54EB005 149) and is funded by KUKA Laboratories GmbH (Augsburg, Germany).
PY - 2015/3
Y1 - 2015/3
N2 - Purpose: The integration of a robot into an image-guided therapy system is still a time consuming process, due to the lack of a well-accepted standard for interdevice communication. The aim of this project is to simplify this procedure by developing an open interface based on three interface classes: state control, visualisation, and sensor. A state machine on the robot control is added to the concept because the robot has its own workflow during surgical procedures, which differs from the workflow of the surgeon.Methods: A KUKA Light Weight Robot is integrated into the medical technology environment of the Institute of Mechatronic Systems as a proof of concept. Therefore, 3D Slicer was used as visualisation and state control software. For the network communication the OpenIGTLink protocol was implemented. In order to achieve high rate control of the robot the “KUKA Sunrise. Connectivity SmartServo” package was used. An exemplary state machine providing states typically used by image-guided therapy interventions, was implemented. Two interface classes, which allow for a direct use of OpenIGTLink for robot control on the one hand and visualisation on the other hand were developed. Additionally, a 3D Slicer module was written to operate the state control.Results: Utilising the described software concept the state machine could be operated by the 3D Slicer module with 20 Hz cycle rate and no data loss was detected during a test phase of approximately 270 s (13,640 packages). Furthermore, the current robot pose could be sent with more than 60 Hz. No influence on the performance of the state machine by the communication thread could be measured.Conclusion: Simplified integration was achieved by using only one programming context for the implementation of the state machine, the interfaces, and the robot control. Eventually, the exemplary state machine can be easily expanded by adding new states.
AB - Purpose: The integration of a robot into an image-guided therapy system is still a time consuming process, due to the lack of a well-accepted standard for interdevice communication. The aim of this project is to simplify this procedure by developing an open interface based on three interface classes: state control, visualisation, and sensor. A state machine on the robot control is added to the concept because the robot has its own workflow during surgical procedures, which differs from the workflow of the surgeon.Methods: A KUKA Light Weight Robot is integrated into the medical technology environment of the Institute of Mechatronic Systems as a proof of concept. Therefore, 3D Slicer was used as visualisation and state control software. For the network communication the OpenIGTLink protocol was implemented. In order to achieve high rate control of the robot the “KUKA Sunrise. Connectivity SmartServo” package was used. An exemplary state machine providing states typically used by image-guided therapy interventions, was implemented. Two interface classes, which allow for a direct use of OpenIGTLink for robot control on the one hand and visualisation on the other hand were developed. Additionally, a 3D Slicer module was written to operate the state control.Results: Utilising the described software concept the state machine could be operated by the 3D Slicer module with 20 Hz cycle rate and no data loss was detected during a test phase of approximately 270 s (13,640 packages). Furthermore, the current robot pose could be sent with more than 60 Hz. No influence on the performance of the state machine by the communication thread could be measured.Conclusion: Simplified integration was achieved by using only one programming context for the implementation of the state machine, the interfaces, and the robot control. Eventually, the exemplary state machine can be easily expanded by adding new states.
KW - 3D Slicer
KW - Finite state machine
KW - Robot control interface
KW - Visualisation
UR - http://www.scopus.com/inward/record.url?scp=84939888776&partnerID=8YFLogxK
U2 - 10.1007/s11548-014-1081-1
DO - 10.1007/s11548-014-1081-1
M3 - Review article
C2 - 24923473
AN - SCOPUS:84939888776
VL - 10
SP - 285
EP - 292
JO - International journal of computer assisted radiology and surgery
JF - International journal of computer assisted radiology and surgery
SN - 1861-6410
IS - 3
ER -