Details
| Translated title of the contribution | Mechanischer Stress und Verformung in den Rotoren einer Hochdrehzahl-PMSM und einer Hochdrehzahl-IM |
|---|---|
| Original language | English |
| Pages (from-to) | 96-109 |
| Number of pages | 14 |
| Journal | Elektrotechnik und Informationstechnik |
| Volume | 138 |
| Issue number | 2 |
| Early online date | 2 Mar 2021 |
| Publication status | Published - Apr 2021 |
Abstract
High-speed electric machines are gaining importance in the field of traction drives and aviation due to their high power density. The evaluation of the mechanical stress in the rotor is one crucial part in the design process for this type of machines. The mechanical stress cannot be measured directly. Accordingly, a validation of the calculated mechanical stress is difficult and normally not performed. Instead of the mechanical stress, the deformation at the rotor surface can be measured using a spin test machine with distance sensors. The deformation can then be used to validate the calculation results. In this paper, the mechanical load exerted on an IM rotor for a 60kW/200001min high-speed electric machine and an PMSM rotor for a 75kW/250001min high-speed electric machine is analysed in detail. The mechanical stress and the deformation are calculated and analysed using a FEM simulation model. Then, a spin test is performed on the two rotors. First, the burst speed is determined by operating two rotor samples above their defined test speed. Then, the deformation is measured at the rotor surface for different operating speeds and the defined test speed. The measurement and the simulation results are compared and discussed. It can be shown that the two designs do not exceed the maximum mechanical stress for the defined operating range. In the deformation measurement of the IM rotor, a plastic deformation up to εIM, pl= 8 μm and elastic deformation up to εIM, el= 22 μm can be seen. In regards to plastics, PMSM rotor expands up to εPMSM, pl= 5 μm. The maximum elastic deformation of the PMSM rotor is εPMSM, el= 40 μm. The comparison of the calculated and the measured elastic deformation shows good accordance for the two rotor types. Both models are capable of describing the deformation and the state of stress in the rotors. In burst tests, both rotors withstand rotational speeds far above the defined test speed.
ASJC Scopus subject areas
- Engineering(all)
- Electrical and Electronic Engineering
Cite this
- Standard
- Harvard
- Apa
- Vancouver
- BibTeX
- RIS
In: Elektrotechnik und Informationstechnik, Vol. 138, No. 2, 04.2021, p. 96-109.
Research output: Contribution to journal › Article › Research › peer review
}
TY - JOUR
T1 - Mechanical stress and deformation in the rotors of a high-speed PMSM and IM
AU - Gerlach, Martin Enno
AU - Zajonc, Maximilian
AU - Ponick, Bernd
N1 - Funding Information: This work was supported by the German Federal Ministry of Economic Affairs and Energy on the basis of a decision by the German Bundestag.
PY - 2021/4
Y1 - 2021/4
N2 - High-speed electric machines are gaining importance in the field of traction drives and aviation due to their high power density. The evaluation of the mechanical stress in the rotor is one crucial part in the design process for this type of machines. The mechanical stress cannot be measured directly. Accordingly, a validation of the calculated mechanical stress is difficult and normally not performed. Instead of the mechanical stress, the deformation at the rotor surface can be measured using a spin test machine with distance sensors. The deformation can then be used to validate the calculation results. In this paper, the mechanical load exerted on an IM rotor for a 60kW/200001min high-speed electric machine and an PMSM rotor for a 75kW/250001min high-speed electric machine is analysed in detail. The mechanical stress and the deformation are calculated and analysed using a FEM simulation model. Then, a spin test is performed on the two rotors. First, the burst speed is determined by operating two rotor samples above their defined test speed. Then, the deformation is measured at the rotor surface for different operating speeds and the defined test speed. The measurement and the simulation results are compared and discussed. It can be shown that the two designs do not exceed the maximum mechanical stress for the defined operating range. In the deformation measurement of the IM rotor, a plastic deformation up to εIM, pl= 8 μm and elastic deformation up to εIM, el= 22 μm can be seen. In regards to plastics, PMSM rotor expands up to εPMSM, pl= 5 μm. The maximum elastic deformation of the PMSM rotor is εPMSM, el= 40 μm. The comparison of the calculated and the measured elastic deformation shows good accordance for the two rotor types. Both models are capable of describing the deformation and the state of stress in the rotors. In burst tests, both rotors withstand rotational speeds far above the defined test speed.
AB - High-speed electric machines are gaining importance in the field of traction drives and aviation due to their high power density. The evaluation of the mechanical stress in the rotor is one crucial part in the design process for this type of machines. The mechanical stress cannot be measured directly. Accordingly, a validation of the calculated mechanical stress is difficult and normally not performed. Instead of the mechanical stress, the deformation at the rotor surface can be measured using a spin test machine with distance sensors. The deformation can then be used to validate the calculation results. In this paper, the mechanical load exerted on an IM rotor for a 60kW/200001min high-speed electric machine and an PMSM rotor for a 75kW/250001min high-speed electric machine is analysed in detail. The mechanical stress and the deformation are calculated and analysed using a FEM simulation model. Then, a spin test is performed on the two rotors. First, the burst speed is determined by operating two rotor samples above their defined test speed. Then, the deformation is measured at the rotor surface for different operating speeds and the defined test speed. The measurement and the simulation results are compared and discussed. It can be shown that the two designs do not exceed the maximum mechanical stress for the defined operating range. In the deformation measurement of the IM rotor, a plastic deformation up to εIM, pl= 8 μm and elastic deformation up to εIM, el= 22 μm can be seen. In regards to plastics, PMSM rotor expands up to εPMSM, pl= 5 μm. The maximum elastic deformation of the PMSM rotor is εPMSM, el= 40 μm. The comparison of the calculated and the measured elastic deformation shows good accordance for the two rotor types. Both models are capable of describing the deformation and the state of stress in the rotors. In burst tests, both rotors withstand rotational speeds far above the defined test speed.
KW - burst test
KW - deformation
KW - high-speed electric machines
KW - induction machine
KW - machine design
KW - mechanical stress
KW - overspeed test
KW - permanent magnet machine
KW - von Mises stress
UR - http://www.scopus.com/inward/record.url?scp=85102025752&partnerID=8YFLogxK
U2 - 10.1007/s00502-021-00866-5
DO - 10.1007/s00502-021-00866-5
M3 - Article
AN - SCOPUS:85102025752
VL - 138
SP - 96
EP - 109
JO - Elektrotechnik und Informationstechnik
JF - Elektrotechnik und Informationstechnik
SN - 0932-383X
IS - 2
ER -