Details
| Original language | English |
|---|---|
| Article number | 107705 |
| Journal | International journal of fatigue |
| Volume | 173 |
| Early online date | 6 May 2023 |
| Publication status | Published - Aug 2023 |
Abstract
Combining welding technology with robotics, wire arc additive manufacturing (WAAM) is emerging as a viable method of construction. To facilitate its wider application, in particular with structural integrity in mind, an improved understanding of the fatigue properties of WAAM materials is needed. Hence, an experimental investigation into the fatigue crack growth (FCG) behaviour of WAAM plates made of normal- and high-strength steels has been conducted and is reported herein. Following material characterisation, FCG tests on 13 machined compact tension specimens were undertaken, extracted in different directions from WAAM plates built using a parallel deposition strategy. Fractography of the tested specimens was also performed to analyse the mechanisms of crack growth. The material testing demonstrated an approximately proportional relationship between the hardness and ultimate strength. From the FCG tests, Paris’ law constants were derived for the WAAM normal- and high-strength steel specimens, revealing consistently lower material constants m for the latter. Similar FCG behaviour to that of equivalent, conventionally-produced steels, with no significant anisotropy, was found. The observed response was shown to be generally well captured by the FCG laws given in BS 7910, with the recommended curve for unwelded steels providing a close match to the experimental data and the recommended curve for welded steels providing conservative predictions. Additional FCG data on WAAM steels printed using the parallel and oscillatory deposition strategies were collected and analysed. It was shown that the two deposition strategies led to similar crack growth rates for WAAM normal-strength steels, but distinct FCG behavioural trends for WAAM high-strength steels. Finally, the fractographic analysis showed that the WAAM specimens exhibited principally brittle behaviour during FCG but somewhat ductile behaviour before fracture.
Keywords
- Additive manufacturing, Compact tension specimen, Fatigue crack propagation, Metal 3D printing, Wire arc additive manufacturing
ASJC Scopus subject areas
- Mathematics(all)
- Modelling and Simulation
- Materials Science(all)
- General Materials Science
- Engineering(all)
- Mechanics of Materials
- Engineering(all)
- Mechanical Engineering
- Engineering(all)
- Industrial and Manufacturing Engineering
Cite this
- Standard
- Harvard
- Apa
- Vancouver
- BibTeX
- RIS
In: International journal of fatigue, Vol. 173, 107705, 08.2023.
Research output: Contribution to journal › Article › Research › peer review
}
TY - JOUR
T1 - Fatigue crack growth behaviour of wire arc additively manufactured steels
AU - Huang, Cheng
AU - Zheng, Yuanpeng
AU - Chen, Tao
AU - Ghafoori, Elyas
AU - Gardner, Leroy
N1 - Funding Information: This research was possible thanks to funding and support from the European Union's Horizon 2020 research and innovation programme under grant agreement No. 820776 ‘Intelligent data driven pipeline for the manufacturing of certified metal parts through Direct Energy Deposition process (INTEGRADDE).’ The authors also gratefully acknowledge MX3D for the provision of the test specimens.
PY - 2023/8
Y1 - 2023/8
N2 - Combining welding technology with robotics, wire arc additive manufacturing (WAAM) is emerging as a viable method of construction. To facilitate its wider application, in particular with structural integrity in mind, an improved understanding of the fatigue properties of WAAM materials is needed. Hence, an experimental investigation into the fatigue crack growth (FCG) behaviour of WAAM plates made of normal- and high-strength steels has been conducted and is reported herein. Following material characterisation, FCG tests on 13 machined compact tension specimens were undertaken, extracted in different directions from WAAM plates built using a parallel deposition strategy. Fractography of the tested specimens was also performed to analyse the mechanisms of crack growth. The material testing demonstrated an approximately proportional relationship between the hardness and ultimate strength. From the FCG tests, Paris’ law constants were derived for the WAAM normal- and high-strength steel specimens, revealing consistently lower material constants m for the latter. Similar FCG behaviour to that of equivalent, conventionally-produced steels, with no significant anisotropy, was found. The observed response was shown to be generally well captured by the FCG laws given in BS 7910, with the recommended curve for unwelded steels providing a close match to the experimental data and the recommended curve for welded steels providing conservative predictions. Additional FCG data on WAAM steels printed using the parallel and oscillatory deposition strategies were collected and analysed. It was shown that the two deposition strategies led to similar crack growth rates for WAAM normal-strength steels, but distinct FCG behavioural trends for WAAM high-strength steels. Finally, the fractographic analysis showed that the WAAM specimens exhibited principally brittle behaviour during FCG but somewhat ductile behaviour before fracture.
AB - Combining welding technology with robotics, wire arc additive manufacturing (WAAM) is emerging as a viable method of construction. To facilitate its wider application, in particular with structural integrity in mind, an improved understanding of the fatigue properties of WAAM materials is needed. Hence, an experimental investigation into the fatigue crack growth (FCG) behaviour of WAAM plates made of normal- and high-strength steels has been conducted and is reported herein. Following material characterisation, FCG tests on 13 machined compact tension specimens were undertaken, extracted in different directions from WAAM plates built using a parallel deposition strategy. Fractography of the tested specimens was also performed to analyse the mechanisms of crack growth. The material testing demonstrated an approximately proportional relationship between the hardness and ultimate strength. From the FCG tests, Paris’ law constants were derived for the WAAM normal- and high-strength steel specimens, revealing consistently lower material constants m for the latter. Similar FCG behaviour to that of equivalent, conventionally-produced steels, with no significant anisotropy, was found. The observed response was shown to be generally well captured by the FCG laws given in BS 7910, with the recommended curve for unwelded steels providing a close match to the experimental data and the recommended curve for welded steels providing conservative predictions. Additional FCG data on WAAM steels printed using the parallel and oscillatory deposition strategies were collected and analysed. It was shown that the two deposition strategies led to similar crack growth rates for WAAM normal-strength steels, but distinct FCG behavioural trends for WAAM high-strength steels. Finally, the fractographic analysis showed that the WAAM specimens exhibited principally brittle behaviour during FCG but somewhat ductile behaviour before fracture.
KW - Additive manufacturing
KW - Compact tension specimen
KW - Fatigue crack propagation
KW - Metal 3D printing
KW - Wire arc additive manufacturing
UR - http://www.scopus.com/inward/record.url?scp=85159096092&partnerID=8YFLogxK
U2 - 10.1016/j.ijfatigue.2023.107705
DO - 10.1016/j.ijfatigue.2023.107705
M3 - Article
AN - SCOPUS:85159096092
VL - 173
JO - International journal of fatigue
JF - International journal of fatigue
SN - 0142-1123
M1 - 107705
ER -