Details
| Original language | English |
|---|---|
| Article number | 105389 |
| Journal | Soil and Tillage Research |
| Volume | 221 |
| Early online date | 18 Apr 2022 |
| Publication status | Published - Jul 2022 |
Abstract
Prevention of soil compaction requires examining soil mechanical stability. This is usually done by applying the basic concept of the pre-compression stress σp, assuming a fully elastic behavior for soils being loaded by stresses lower than σp and a mixture of elastic-plastic behavior being loaded by higher stresses. However, a small cumulative plastic deformation may occur even when the applied stresses is not beyond σp being indeterminable by current pe-compression test procedures which is not accounting for unloading steps. Therefore, we investigated an alternative approach to simultaneously determine σp and mechanical elasticity of soil by introducing unloading steps (referred to as release compression, RC). Results were compared to the conventional procedure with continuously increasing loads (continuous compression, CC). In the case of RC, soil settlement was measured both after each loading (RC-L) and after each unloading (RC-U) phases between two consecutive pressures providing two load displacement curves. Oedometer tests were conducted with three different soils comprising different clay contents ranging from 75 to 454 g kg−1. Remolded soil was filled into steel rings and compressed under pre-determined loads in a loading frame providing test samples with known pre-compression stresses of 60 and 120 kPa. The results revealed that σp values determined under two different applied loading paths (RC vs. CC) were significantly different. Both testing approaches resulted in an overestimation of σp values based on stress-strain curves which was more pronounced for RC-L compared to CC paths. However, the results from RC-U paths were closer to the CC method than the RC-L path suggesting that if an unloading step is used, RC-U curve should be used to determine σp values. The results also showed that soil with higher clay contents comprised the lowest σp value determined from the oedometer tests among all examined soils. From release compression test, we were also able to determine the elasticity of the sample for each loading stress. Among the examined soil samples, the clay soil (with higher clay content) showed the highest elasticity index being less susceptible to soil deformation.
Keywords
- Deformation, Elasticity index, Pre-compression stress, Stress-strain curve
ASJC Scopus subject areas
- Agricultural and Biological Sciences(all)
- Agronomy and Crop Science
- Agricultural and Biological Sciences(all)
- Soil Science
- Earth and Planetary Sciences(all)
- Earth-Surface Processes
Cite this
- Standard
- Harvard
- Apa
- Vancouver
- BibTeX
- RIS
In: Soil and Tillage Research, Vol. 221, 105389, 07.2022.
Research output: Contribution to journal › Article › Research › peer review
}
TY - JOUR
T1 - Assessment of mechanical elasticity of soils based on confined compression tests
AU - Mousavi, S. B.
AU - Uteau, D.
AU - Peth, S.
N1 - Funding Information: S.B.M. is thankful for the cooperation from International & Scientific Cooperation Office of University of Maragheh. S.B.M gratefully acknowledges the support received from Kassel University. Authors appreciate the help received from Mrs. Rode during lab work.
PY - 2022/7
Y1 - 2022/7
N2 - Prevention of soil compaction requires examining soil mechanical stability. This is usually done by applying the basic concept of the pre-compression stress σp, assuming a fully elastic behavior for soils being loaded by stresses lower than σp and a mixture of elastic-plastic behavior being loaded by higher stresses. However, a small cumulative plastic deformation may occur even when the applied stresses is not beyond σp being indeterminable by current pe-compression test procedures which is not accounting for unloading steps. Therefore, we investigated an alternative approach to simultaneously determine σp and mechanical elasticity of soil by introducing unloading steps (referred to as release compression, RC). Results were compared to the conventional procedure with continuously increasing loads (continuous compression, CC). In the case of RC, soil settlement was measured both after each loading (RC-L) and after each unloading (RC-U) phases between two consecutive pressures providing two load displacement curves. Oedometer tests were conducted with three different soils comprising different clay contents ranging from 75 to 454 g kg−1. Remolded soil was filled into steel rings and compressed under pre-determined loads in a loading frame providing test samples with known pre-compression stresses of 60 and 120 kPa. The results revealed that σp values determined under two different applied loading paths (RC vs. CC) were significantly different. Both testing approaches resulted in an overestimation of σp values based on stress-strain curves which was more pronounced for RC-L compared to CC paths. However, the results from RC-U paths were closer to the CC method than the RC-L path suggesting that if an unloading step is used, RC-U curve should be used to determine σp values. The results also showed that soil with higher clay contents comprised the lowest σp value determined from the oedometer tests among all examined soils. From release compression test, we were also able to determine the elasticity of the sample for each loading stress. Among the examined soil samples, the clay soil (with higher clay content) showed the highest elasticity index being less susceptible to soil deformation.
AB - Prevention of soil compaction requires examining soil mechanical stability. This is usually done by applying the basic concept of the pre-compression stress σp, assuming a fully elastic behavior for soils being loaded by stresses lower than σp and a mixture of elastic-plastic behavior being loaded by higher stresses. However, a small cumulative plastic deformation may occur even when the applied stresses is not beyond σp being indeterminable by current pe-compression test procedures which is not accounting for unloading steps. Therefore, we investigated an alternative approach to simultaneously determine σp and mechanical elasticity of soil by introducing unloading steps (referred to as release compression, RC). Results were compared to the conventional procedure with continuously increasing loads (continuous compression, CC). In the case of RC, soil settlement was measured both after each loading (RC-L) and after each unloading (RC-U) phases between two consecutive pressures providing two load displacement curves. Oedometer tests were conducted with three different soils comprising different clay contents ranging from 75 to 454 g kg−1. Remolded soil was filled into steel rings and compressed under pre-determined loads in a loading frame providing test samples with known pre-compression stresses of 60 and 120 kPa. The results revealed that σp values determined under two different applied loading paths (RC vs. CC) were significantly different. Both testing approaches resulted in an overestimation of σp values based on stress-strain curves which was more pronounced for RC-L compared to CC paths. However, the results from RC-U paths were closer to the CC method than the RC-L path suggesting that if an unloading step is used, RC-U curve should be used to determine σp values. The results also showed that soil with higher clay contents comprised the lowest σp value determined from the oedometer tests among all examined soils. From release compression test, we were also able to determine the elasticity of the sample for each loading stress. Among the examined soil samples, the clay soil (with higher clay content) showed the highest elasticity index being less susceptible to soil deformation.
KW - Deformation
KW - Elasticity index
KW - Pre-compression stress
KW - Stress-strain curve
UR - http://www.scopus.com/inward/record.url?scp=85128311819&partnerID=8YFLogxK
U2 - 10.1016/j.still.2022.105389
DO - 10.1016/j.still.2022.105389
M3 - Article
AN - SCOPUS:85128311819
VL - 221
JO - Soil and Tillage Research
JF - Soil and Tillage Research
SN - 0167-1987
M1 - 105389
ER -