Organisation placeholder image, no image found

Institute of Machine Elements and Engineering Design

Organisational unit: Institute

Type of address: Visitor address.
Welfengarten 1 A
30167
Hannover
View graph of relations
141 - 160 out of 327Page size: 20

Publications

  1. 2018
  2. Published

    Sonderforschungsbereich 1153, Wälzfestigkeit

    Poll, G., Coors, T. & Pape, F., Apr 2018.

    Research output: Contribution to conference › Poster › Research

  3. Published

    Friction torque of wind-turbine pitch bearings – comparison of experimental results with available models

    Stammler, M., Schwack, F., Bader, N., Reuter, A. & Poll, G., 14 Mar 2018, In: Wind Energy Science. 3, 1, p. 97-105 9 p.

    Research output: Contribution to journal › Article › Research › peer review

  4. Published

    Investigations on the frictional behavior of soft and hard contact lenses by nanoscratch studies

    Poll, G., Pape, F., Matthias, T. & Behrens, B., Feb 2018.

    Research output: Contribution to conference › Poster › Research

  5. Published

    Analyse der Bauteilbewegungen und Verschleißuntersuchungen an Synchronisierungen im nicht geschalteten Zustand

    Poll, G. & Niemeier, M. A., 2018, Forschungsheft 1312 der Forschungsvereinigung Antriebstechnik e. V.. Frankfurt

    Research output: Chapter in book/report/conference proceeding › Contribution to project report/research report › Research

  6. Published

    Beanspruchung von Kupplungskörpern

    Pfeifer, B., 2018, Hannover. 115 p.

    Research output: Thesis › Doctoral thesis

  7. Published

    Capacitance Measurement of Film Thickness in EHL contacts

    Bader, N. F., Liu, H., Furtmann, A., Zhang, B. & Poll, G., 2018, Proceedings. p. 77-78

    Research output: Chapter in book/report/conference proceeding › Conference contribution › Research

  8. Published

    Computational approach to improve bearings by residual stresses based on their required bearing fatigue life

    Pape, F., Maiss, O., Denkena, B. & Poll, G., 2018, In: International Journal of Computational Methods and Experimental Measurements. 6, 4, p. 656-666 11 p.

    Research output: Contribution to journal › Article › Research › peer review

  9. Published

    Enhancing Machine Elements by Residual Stresses, Optimized Surfaces and Tailored Forming

    Poll, G., Coors, T. & Pape, F., 2018, Proceedings. p. 277-278

    Research output: Chapter in book/report/conference proceeding › Conference contribution › Research

  10. Published

    Erweiterung der Wälzlagerberechnung in FVA-Software (FVA 701 III)

    Poll, G., Schneider, V., Stahl, K. & Zander, M., 2018.

    Research output: Contribution to conference › Paper › Research

  11. Published

    Experimentelle und theoretische Untersuchungen zum Reibverhalten elastomerer Werkstoffe auf rauen Oberflächen

    Lang, A., 2018, Hannover. 235 p.

    Research output: Thesis › Doctoral thesis

  12. Published

    Friction reduction and reliable sealing with rotating radial shaft seals

    Pelzer, V. & Poll, G., 2018, p. 133-141. 9 p.

    Research output: Contribution to conference › Paper › Research › peer review

  13. Published

    Herstellungsprozess und Wälzfestigkeit von hybriden Hochleistungsbauteilen

    Mildebrath, M., Maier, H. J., Hassel, T., Coors, T., Pape, F., Poll, G., Barroi, A., Lammers, M., Hermsdorf, J. & Overmeyer, L., 2018, In: Konstruktion. 70, 9, p. 84-89 6 p.

    Research output: Contribution to journal › Review article › Research

  14. Published

    Improvement of the frictional properties of angular contact ball bearings operating under small pivoting angles by surface texturing

    Poll, G., Pape, F., Maiß, O., Lucas, H. & Denkena, B., 2018, Proceedings.

    Research output: Chapter in book/report/conference proceeding › Conference contribution › Research

  15. Published

    Investigation of the Lubricant Distribution in a High-Speed Gearbox

    Poll, G. & Friedl, A., 2018, Proceedings. p. 179-179

    Research output: Chapter in book/report/conference proceeding › Conference contribution › Research

  16. Published

    Kontinuierliche Messung des Rückförderverhaltens von Radialwellendichtungen

    Poll, G., Matus, M. P., Pelzer, V. & Wennehorst, B., 2018.

    Research output: Contribution to conference › Paper › Research

  17. Published

    Radial Lip Seal Aging in Synthetic Oil

    Poll, G., Bulut, D., Giese, U. & Seibel, T., 2018, Proceedings. p. 33-34

    Research output: Chapter in book/report/conference proceeding › Conference contribution › Research

  18. Published

    Radially Preloaded Cylindrical Roller Bearings: Optimized Preload and Operating Performance

    Poll, G. & Böttcher, R., 2018, Proceedings. p. 85-86

    Research output: Chapter in book/report/conference proceeding › Conference contribution › Research

  19. Published

    Radially preloaded cylindrical roller bearings – experimental studies regarding axial roller kinematic

    Poll, G. & Böttcher, R., 2018, Proceedings.

    Research output: Chapter in book/report/conference proceeding › Conference contribution › Research

  20. Published

    Rotor blade bearing lubrication, wear and failure mechanisms

    Poll, G., 2018.

    Research output: Contribution to conference › Paper › Research

  21. Published

    Schutzdichtungen für Wälzlager III.

    Poll, G. & Poltavchenko, V., 2018, Forschungsheft 1315 der Forschungsvereinigung Antriebstechnik e. V.. Frankfurt

    Research output: Chapter in book/report/conference proceeding › Contribution to project report/research report › Research

Previous 1...4 5 6 7 8 9 10 11 ...17 Next