Details
| Originalsprache | Englisch |
|---|---|
| Aufsatznummer | 111560 |
| Fachzeitschrift | Solar Energy Materials and Solar Cells |
| Jahrgang | 238 |
| Frühes Online-Datum | 20 Jan. 2022 |
| Publikationsstatus | Veröffentlicht - Mai 2022 |
Abstract
We conduct numerical device simulations to study to what extend poly-Si on oxide (POLO)2 IBC solar cells can be optimized. In particular, we evaluate the benefit of the concept of photonic crystals (PCs) for “standard” cell thicknesses compatible with industrial wafer handling. We find that for our current surface passivation quality, implementing PCs and decreasing the wafer thickness down to 15 μm would increase the efficiency by „only“ 1% absolute due to limiting surface recombination losses. We deduce a high c-Si/SiOx interface state density Dit of 2.9 × 1012 eV−1cm−2 by analyzing special two-terminal IV measurements on small pads that contact the intact interfacial oxide between pinholes with our MarcoPOLO model. Consequently, we improve the hydrogenation process of our POLO junctions by an Al2O3/SiNx/Al2O3 rear-side dielectric layer stack. For n-type POLO (p-type POLO) J0 is reduced from 4 (10) fA/cm2 down to 0.5 ± 0.3 (3.3 ± 0.7) fA/cm2. For this improved surface passivation, our numerical device simulations predict an efficiency potential of 29.1% (27.8%) for POLO2 IBC cells with (without) PCs for a standard thickness of 150 μm. This shows that the “practical limit” for Si solar cells with poly-Si on oxide-based passivating contact schemes is above 27%, and, in general, that the efficiency potential of Si single-junction cells is still far from being exhausted. The first implementation of the improved POLO junctions into cell precursors confirms the predicted improvement on the level of suns - implied open-circuit voltage curves.
ASJC Scopus Sachgebiete
- Werkstoffwissenschaften (insg.)
- Elektronische, optische und magnetische Materialien
- Energie (insg.)
- Erneuerbare Energien, Nachhaltigkeit und Umwelt
- Werkstoffwissenschaften (insg.)
- Oberflächen, Beschichtungen und Folien
Ziele für nachhaltige Entwicklung
Zitieren
- Standard
- Harvard
- Apa
- Vancouver
- BibTex
- RIS
in: Solar Energy Materials and Solar Cells, Jahrgang 238, 111560, 05.2022.
Publikation: Beitrag in Fachzeitschrift › Artikel › Forschung › Peer-Review
}
TY - JOUR
T1 - Towards 28 %-efficient Si single-junction solar cells with better passivating POLO junctions and photonic crystals
AU - Peibst, R.
AU - Rienäcker, M.
AU - Larionova, Y.
AU - Folchert, N.
AU - Haase, F.
AU - Hollemann, C.
AU - Wolter, S.
AU - Krügener, J.
AU - Bayerl, P.
AU - Bayer, J.
AU - Dzinnik, M.
AU - Haug, R. J.
AU - Brendel, R.
N1 - Funding Information: We would like to thank H. Fischer, S. Spätlich, R. Winter, A. Raugewitz,G. Glowatzki and R. Zieseniβ for sample processing, M. Wolf, A. Dietrich, R. Reineke-Koch for discussion and support with the measurement systems, and Sajeev John for fruitful discussions. This work is funded by the German Ministry for Economic Affairs and Energy (grant FKZ 003EE1056A ), by the federal state of Lower Saxony and by the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation) under Germany's Excellence Strategy - EXC-2123 QuantumFrontiers – 390837967.
PY - 2022/5
Y1 - 2022/5
N2 - We conduct numerical device simulations to study to what extend poly-Si on oxide (POLO)2 IBC solar cells can be optimized. In particular, we evaluate the benefit of the concept of photonic crystals (PCs) for “standard” cell thicknesses compatible with industrial wafer handling. We find that for our current surface passivation quality, implementing PCs and decreasing the wafer thickness down to 15 μm would increase the efficiency by „only“ 1% absolute due to limiting surface recombination losses. We deduce a high c-Si/SiOx interface state density Dit of 2.9 × 1012 eV−1cm−2 by analyzing special two-terminal IV measurements on small pads that contact the intact interfacial oxide between pinholes with our MarcoPOLO model. Consequently, we improve the hydrogenation process of our POLO junctions by an Al2O3/SiNx/Al2O3 rear-side dielectric layer stack. For n-type POLO (p-type POLO) J0 is reduced from 4 (10) fA/cm2 down to 0.5 ± 0.3 (3.3 ± 0.7) fA/cm2. For this improved surface passivation, our numerical device simulations predict an efficiency potential of 29.1% (27.8%) for POLO2 IBC cells with (without) PCs for a standard thickness of 150 μm. This shows that the “practical limit” for Si solar cells with poly-Si on oxide-based passivating contact schemes is above 27%, and, in general, that the efficiency potential of Si single-junction cells is still far from being exhausted. The first implementation of the improved POLO junctions into cell precursors confirms the predicted improvement on the level of suns - implied open-circuit voltage curves.
AB - We conduct numerical device simulations to study to what extend poly-Si on oxide (POLO)2 IBC solar cells can be optimized. In particular, we evaluate the benefit of the concept of photonic crystals (PCs) for “standard” cell thicknesses compatible with industrial wafer handling. We find that for our current surface passivation quality, implementing PCs and decreasing the wafer thickness down to 15 μm would increase the efficiency by „only“ 1% absolute due to limiting surface recombination losses. We deduce a high c-Si/SiOx interface state density Dit of 2.9 × 1012 eV−1cm−2 by analyzing special two-terminal IV measurements on small pads that contact the intact interfacial oxide between pinholes with our MarcoPOLO model. Consequently, we improve the hydrogenation process of our POLO junctions by an Al2O3/SiNx/Al2O3 rear-side dielectric layer stack. For n-type POLO (p-type POLO) J0 is reduced from 4 (10) fA/cm2 down to 0.5 ± 0.3 (3.3 ± 0.7) fA/cm2. For this improved surface passivation, our numerical device simulations predict an efficiency potential of 29.1% (27.8%) for POLO2 IBC cells with (without) PCs for a standard thickness of 150 μm. This shows that the “practical limit” for Si solar cells with poly-Si on oxide-based passivating contact schemes is above 27%, and, in general, that the efficiency potential of Si single-junction cells is still far from being exhausted. The first implementation of the improved POLO junctions into cell precursors confirms the predicted improvement on the level of suns - implied open-circuit voltage curves.
UR - http://www.scopus.com/inward/record.url?scp=85123118845&partnerID=8YFLogxK
U2 - 10.1016/j.solmat.2021.111560
DO - 10.1016/j.solmat.2021.111560
M3 - Article
AN - SCOPUS:85123118845
VL - 238
JO - Solar Energy Materials and Solar Cells
JF - Solar Energy Materials and Solar Cells
SN - 0927-0248
M1 - 111560
ER -