Details
| Originalsprache | Englisch |
|---|---|
| Seiten (von - bis) | 587-593 |
| Seitenumfang | 7 |
| Fachzeitschrift | Production Engineering |
| Jahrgang | 15 |
| Ausgabenummer | 3-4 |
| Frühes Online-Datum | 19 Feb. 2021 |
| Publikationsstatus | Veröffentlicht - Juni 2021 |
Abstract
Deep rolling is a machining process which is used to decrease roughness and to induce compressive residual stresses into component surfaces. A recent publication of this research group showed possibilities to predict the topography during deep rolling of bars in a lathe. Although deep rolling can be used in a milling machine to machine flat specimens, it is still unclear, whether the topography can be predicted to a similar extend using this application. To investigate the influence of the machining parameters on topography, three experimental stages are performed in this paper on cast AlSi10Mg. First, single-track deep rolling experiments are performed under variation of the deep rolling pressure pw to find the relationship between pw and the indentation geometry. Here, a logarithmic relationship between deep rolling pressure and the indentation characteristics could be found that achieved a relatively high agreement. In the second stage, surfaces are prepared using multi-track deep rolling. Here, the deep rolling pressure pw and the lateral displacement ab are varied. The multi-track rolled surfaces were compared to an analytical model for the calculation of the theoretical roughness that is based on the logarithmic relationship found in the first experimental stage. Here, the limits of the analytical prediction were shown because high similarities between predicted and measured surfaces only occurred for certain deep rolling pressures pw and lateral displacements ab. To further investigate the limitations of this procedure, a novel tool concept, which utilizes the rotation of the machine spindle, is used in the third stage. Here, the generated surface can also be interpreted as a periodic sequence of spheric indentations as shown in the second experimental stage, whereas the measured surfaces differed from the expected surfaces. As a result of this paper, the predictability of the surface topography after deep rolling of flat specimens is known (minimum pressure pw,minAlSi10Mg = 5 MPa and minimum lateral displacement ab,minAlSi10Mg = 0.25 mm) and also first results regarding the final topography after using the novel tool concept are presented.
ASJC Scopus Sachgebiete
- Ingenieurwesen (insg.)
- Maschinenbau
- Ingenieurwesen (insg.)
- Wirtschaftsingenieurwesen und Fertigungstechnik
Zitieren
- Standard
- Harvard
- Apa
- Vancouver
- BibTex
- RIS
in: Production Engineering, Jahrgang 15, Nr. 3-4, 06.2021, S. 587-593.
Publikation: Beitrag in Fachzeitschrift › Artikel › Forschung › Peer-Review
}
TY - JOUR
T1 - Surface topography after deep rolling with milling kinematics
AU - Denkena, Berend
AU - Krödel, Alexander
AU - Heikebrügge, Steffen
AU - Meyer, Kolja
AU - Pillkahn, Philipp
N1 - Funding Information: Open Access funding enabled and organized by Projekt DEAL. This research was funded by the Federal Ministry of Economics and Energy (BMWi) via the German Federation of Industrial Research Associations (AiF) e. V., Grant Number IGF-20626 N/1.
PY - 2021/6
Y1 - 2021/6
N2 - Deep rolling is a machining process which is used to decrease roughness and to induce compressive residual stresses into component surfaces. A recent publication of this research group showed possibilities to predict the topography during deep rolling of bars in a lathe. Although deep rolling can be used in a milling machine to machine flat specimens, it is still unclear, whether the topography can be predicted to a similar extend using this application. To investigate the influence of the machining parameters on topography, three experimental stages are performed in this paper on cast AlSi10Mg. First, single-track deep rolling experiments are performed under variation of the deep rolling pressure pw to find the relationship between pw and the indentation geometry. Here, a logarithmic relationship between deep rolling pressure and the indentation characteristics could be found that achieved a relatively high agreement. In the second stage, surfaces are prepared using multi-track deep rolling. Here, the deep rolling pressure pw and the lateral displacement ab are varied. The multi-track rolled surfaces were compared to an analytical model for the calculation of the theoretical roughness that is based on the logarithmic relationship found in the first experimental stage. Here, the limits of the analytical prediction were shown because high similarities between predicted and measured surfaces only occurred for certain deep rolling pressures pw and lateral displacements ab. To further investigate the limitations of this procedure, a novel tool concept, which utilizes the rotation of the machine spindle, is used in the third stage. Here, the generated surface can also be interpreted as a periodic sequence of spheric indentations as shown in the second experimental stage, whereas the measured surfaces differed from the expected surfaces. As a result of this paper, the predictability of the surface topography after deep rolling of flat specimens is known (minimum pressure pw,minAlSi10Mg = 5 MPa and minimum lateral displacement ab,minAlSi10Mg = 0.25 mm) and also first results regarding the final topography after using the novel tool concept are presented.
AB - Deep rolling is a machining process which is used to decrease roughness and to induce compressive residual stresses into component surfaces. A recent publication of this research group showed possibilities to predict the topography during deep rolling of bars in a lathe. Although deep rolling can be used in a milling machine to machine flat specimens, it is still unclear, whether the topography can be predicted to a similar extend using this application. To investigate the influence of the machining parameters on topography, three experimental stages are performed in this paper on cast AlSi10Mg. First, single-track deep rolling experiments are performed under variation of the deep rolling pressure pw to find the relationship between pw and the indentation geometry. Here, a logarithmic relationship between deep rolling pressure and the indentation characteristics could be found that achieved a relatively high agreement. In the second stage, surfaces are prepared using multi-track deep rolling. Here, the deep rolling pressure pw and the lateral displacement ab are varied. The multi-track rolled surfaces were compared to an analytical model for the calculation of the theoretical roughness that is based on the logarithmic relationship found in the first experimental stage. Here, the limits of the analytical prediction were shown because high similarities between predicted and measured surfaces only occurred for certain deep rolling pressures pw and lateral displacements ab. To further investigate the limitations of this procedure, a novel tool concept, which utilizes the rotation of the machine spindle, is used in the third stage. Here, the generated surface can also be interpreted as a periodic sequence of spheric indentations as shown in the second experimental stage, whereas the measured surfaces differed from the expected surfaces. As a result of this paper, the predictability of the surface topography after deep rolling of flat specimens is known (minimum pressure pw,minAlSi10Mg = 5 MPa and minimum lateral displacement ab,minAlSi10Mg = 0.25 mm) and also first results regarding the final topography after using the novel tool concept are presented.
KW - Burnishing
KW - Deep rolling
KW - Roughness
KW - Surface integrity
KW - Topography
UR - http://www.scopus.com/inward/record.url?scp=85101285741&partnerID=8YFLogxK
U2 - 10.1007/s11740-021-01031-9
DO - 10.1007/s11740-021-01031-9
M3 - Article
AN - SCOPUS:85101285741
VL - 15
SP - 587
EP - 593
JO - Production Engineering
JF - Production Engineering
SN - 0944-6524
IS - 3-4
ER -