Details
| Titel in Übersetzung | Überblick und Vergleich von Testmethoden für die Bewertung der Umformbarkeit einer geschnittenen Blechkante sowie Ansätze zur Nutzung der Versuchsergebnisse in der Umformsimulation |
|---|---|
| Originalsprache | Englisch |
| Seiten (von - bis) | 1196-1217 |
| Seitenumfang | 22 |
| Fachzeitschrift | Materialwissenschaft und Werkstofftechnik |
| Jahrgang | 46 |
| Ausgabenummer | 12 |
| Publikationsstatus | Veröffentlicht - 8 Dez. 2015 |
Abstract
This paper presents an overview of published test methods for determination of formability of a sheet metal cut-edge. The presented test methods were developed to evaluate formability of a sheet metal edge that was produced by shear cutting. Due to high local strains, hardening, or even microcracks, the cut-edge might have less formability than the base material. The presentation of the tests is structured according to the three steps each test can be divided into: cutting, forming and evaluation. Similarities and differences concerning these steps were worked out. Additionally, a classification of the tests is made regarding their strain gradients in the vicinity of the cut-edge. For this, finite element models of exemplary tests were built up using LS-DYNA explicit and analyzed accordingly. Evaluation approaches that go beyond the common hole expansion ratio (HER) from the hole expansion test (HET) standardized in the ISO 16630 are also described. The tests can be used not only for a quantitative comparison of materials and cutting processes with regard to the cut-edge formability but to determine input data for the finite element analysis (FEA) of forming processes to allow a simulation based cut-edge failure prediction. The paper also presents appropriate procedures on the transfer of the test results into the FEA of forming of a workpiece with a cut-edge.
ASJC Scopus Sachgebiete
- Werkstoffwissenschaften (insg.)
- Allgemeine Materialwissenschaften
- Physik und Astronomie (insg.)
- Physik der kondensierten Materie
- Ingenieurwesen (insg.)
- Werkstoffmechanik
- Ingenieurwesen (insg.)
- Maschinenbau
Zitieren
- Standard
- Harvard
- Apa
- Vancouver
- BibTex
- RIS
in: Materialwissenschaft und Werkstofftechnik, Jahrgang 46, Nr. 12, 08.12.2015, S. 1196-1217.
Publikation: Beitrag in Fachzeitschrift › Artikel › Forschung › Peer-Review
}
TY - JOUR
T1 - Overview and comparison of various test methods to determine formability of a sheet metal cut-edge and approaches to the test results application in forming analysis
AU - Schneider, M.
AU - Geffert, A.
AU - Peshekhodov, I.
AU - Behrens, B. A.
PY - 2015/12/8
Y1 - 2015/12/8
N2 - This paper presents an overview of published test methods for determination of formability of a sheet metal cut-edge. The presented test methods were developed to evaluate formability of a sheet metal edge that was produced by shear cutting. Due to high local strains, hardening, or even microcracks, the cut-edge might have less formability than the base material. The presentation of the tests is structured according to the three steps each test can be divided into: cutting, forming and evaluation. Similarities and differences concerning these steps were worked out. Additionally, a classification of the tests is made regarding their strain gradients in the vicinity of the cut-edge. For this, finite element models of exemplary tests were built up using LS-DYNA explicit and analyzed accordingly. Evaluation approaches that go beyond the common hole expansion ratio (HER) from the hole expansion test (HET) standardized in the ISO 16630 are also described. The tests can be used not only for a quantitative comparison of materials and cutting processes with regard to the cut-edge formability but to determine input data for the finite element analysis (FEA) of forming processes to allow a simulation based cut-edge failure prediction. The paper also presents appropriate procedures on the transfer of the test results into the FEA of forming of a workpiece with a cut-edge.
AB - This paper presents an overview of published test methods for determination of formability of a sheet metal cut-edge. The presented test methods were developed to evaluate formability of a sheet metal edge that was produced by shear cutting. Due to high local strains, hardening, or even microcracks, the cut-edge might have less formability than the base material. The presentation of the tests is structured according to the three steps each test can be divided into: cutting, forming and evaluation. Similarities and differences concerning these steps were worked out. Additionally, a classification of the tests is made regarding their strain gradients in the vicinity of the cut-edge. For this, finite element models of exemplary tests were built up using LS-DYNA explicit and analyzed accordingly. Evaluation approaches that go beyond the common hole expansion ratio (HER) from the hole expansion test (HET) standardized in the ISO 16630 are also described. The tests can be used not only for a quantitative comparison of materials and cutting processes with regard to the cut-edge formability but to determine input data for the finite element analysis (FEA) of forming processes to allow a simulation based cut-edge failure prediction. The paper also presents appropriate procedures on the transfer of the test results into the FEA of forming of a workpiece with a cut-edge.
KW - cut-edge
KW - edge crack sensitivity
KW - formability
KW - numerical simulation
KW - Sheet metal
UR - http://www.scopus.com/inward/record.url?scp=84951268020&partnerID=8YFLogxK
U2 - 10.1002/mawe.201500446
DO - 10.1002/mawe.201500446
M3 - Article
AN - SCOPUS:84951268020
VL - 46
SP - 1196
EP - 1217
JO - Materialwissenschaft und Werkstofftechnik
JF - Materialwissenschaft und Werkstofftechnik
SN - 0933-5137
IS - 12
ER -