Details
| Originalsprache | Englisch |
|---|---|
| Seiten (von - bis) | 1619-1627 |
| Seitenumfang | 9 |
| Fachzeitschrift | International Journal of Advanced Manufacturing Technology |
| Jahrgang | 92 |
| Ausgabenummer | 5-8 |
| Publikationsstatus | Veröffentlicht - 16 März 2017 |
Abstract
The grinding process is still an important manufacturing process for the machining of automotive components. For power train components, ultra-high carbon steel (UHC-steel) is a promising new innovative alloy because of its low specific density. Results from turning of UHC-steel showed that the texture of UHC-steel significantly differs from conventional steels. Furthermore, extremely hard carbides, which are embedded into a soft ferrite matrix, result in a UHC-steel specific machining behavior and a high tool wear rate. Therefore, UHC-steel is marked as a difficult-to-cut material. So far, there are no research results available for the grinding of UHC-steel. Therefore, fundamental investigations were conducted in order to analyze the material removal and chip formation mechanisms. Scratching tests with a geometrically defined cubic boron nitride cutting edge showed ductile material removal mechanisms for a single grain chip thickness variation from hcu = 1.5 up to 14 μm. Analysis of the contact zone by means of an innovative quick stop device confirms these results.
ASJC Scopus Sachgebiete
- Ingenieurwesen (insg.)
- Steuerungs- und Systemtechnik
- Informatik (insg.)
- Software
- Ingenieurwesen (insg.)
- Maschinenbau
- Informatik (insg.)
- Angewandte Informatik
- Ingenieurwesen (insg.)
- Wirtschaftsingenieurwesen und Fertigungstechnik
Zitieren
- Standard
- Harvard
- Apa
- Vancouver
- BibTex
- RIS
in: International Journal of Advanced Manufacturing Technology, Jahrgang 92, Nr. 5-8, 16.03.2017, S. 1619-1627.
Publikation: Beitrag in Fachzeitschrift › Artikel › Forschung › Peer-Review
}
TY - JOUR
T1 - Material removal and chip formation mechanisms of UHC-steel during grinding
AU - Denkena, B.
AU - Grove, T.
AU - Göttsching, T.
PY - 2017/3/16
Y1 - 2017/3/16
N2 - The grinding process is still an important manufacturing process for the machining of automotive components. For power train components, ultra-high carbon steel (UHC-steel) is a promising new innovative alloy because of its low specific density. Results from turning of UHC-steel showed that the texture of UHC-steel significantly differs from conventional steels. Furthermore, extremely hard carbides, which are embedded into a soft ferrite matrix, result in a UHC-steel specific machining behavior and a high tool wear rate. Therefore, UHC-steel is marked as a difficult-to-cut material. So far, there are no research results available for the grinding of UHC-steel. Therefore, fundamental investigations were conducted in order to analyze the material removal and chip formation mechanisms. Scratching tests with a geometrically defined cubic boron nitride cutting edge showed ductile material removal mechanisms for a single grain chip thickness variation from hcu = 1.5 up to 14 μm. Analysis of the contact zone by means of an innovative quick stop device confirms these results.
AB - The grinding process is still an important manufacturing process for the machining of automotive components. For power train components, ultra-high carbon steel (UHC-steel) is a promising new innovative alloy because of its low specific density. Results from turning of UHC-steel showed that the texture of UHC-steel significantly differs from conventional steels. Furthermore, extremely hard carbides, which are embedded into a soft ferrite matrix, result in a UHC-steel specific machining behavior and a high tool wear rate. Therefore, UHC-steel is marked as a difficult-to-cut material. So far, there are no research results available for the grinding of UHC-steel. Therefore, fundamental investigations were conducted in order to analyze the material removal and chip formation mechanisms. Scratching tests with a geometrically defined cubic boron nitride cutting edge showed ductile material removal mechanisms for a single grain chip thickness variation from hcu = 1.5 up to 14 μm. Analysis of the contact zone by means of an innovative quick stop device confirms these results.
KW - Chip formation
KW - Grinding
KW - Material removal mechanisms
KW - UHC-steel
UR - http://www.scopus.com/inward/record.url?scp=85015172739&partnerID=8YFLogxK
U2 - 10.1007/s00170-017-0270-9
DO - 10.1007/s00170-017-0270-9
M3 - Article
AN - SCOPUS:85015172739
VL - 92
SP - 1619
EP - 1627
JO - International Journal of Advanced Manufacturing Technology
JF - International Journal of Advanced Manufacturing Technology
SN - 0268-3768
IS - 5-8
ER -