TY - JOUR

T1 - Experimental Investigation of the Sensitivity of Forced Response to Cold Streaks in an Axial Turbine

AU - Stania, Lennart

AU - Ludeneit, Felix

AU - Seume, Joerg R.

N1 - Publisher Copyright: © 2024 by the authors.

PY - 2024/7/2

Y1 - 2024/7/2

N2 - In turbomachinery, geometric variances of the blades, due to manufacturing tolerances, deterioration over a lifetime, or blade repair, can influence overall aerodynamic performance as well as aeroelastic behaviour. In cooled turbine blades, such deviations may lead to streaks of high or low temperature. It has already been shown that hot streaks from the combustors lead to inhomogeneity in the flow path, resulting in increased blade dynamic stress. However, not only hot streaks but also cold streaks occur in modern aircraft engines due to deterioration-induced widening of cooling holes. This work investigates this effect in an experimental setup of a five-stage axial turbine. Cooling air is injected through the vane row of the fourth stage at midspan, and the vibration amplitudes of the blades in rotor stage five are measured with a tip-timing system. The highest injected mass flow rate is 2% of the total mass flow rate for a low-load operating point. The global turbine parameters change between the reference case without cooling air and the cold streak case. This change in operating conditions is compensated such that the corrected operating point is held constant throughout the measurements. It is shown that the cold streak is deflected in the direction of the hub and detected at 40% channel height behind the stator vane of the fifth stage. The averaged vibration amplitude over all blades increases by 20% for the cold streak case compared to the reference during low-load operating of the axial turbine. For operating points with higher loads, however, no increase in averaged vibration amplitude exceeding the measurement uncertainties is observed because the relative cooling mass flow rate is too low. It is shown that the cold streak only influences the pressure side and leads to a widening of the wake deficit. This is identified as the reason for the increased forcing on the blade. The conclusion is that an accurate prediction of the blade’s lifetime requires consideration of the cooling air within the design process and estimation of changes in cooling air mass flow rate throughout the blade’s lifetime.

AB - In turbomachinery, geometric variances of the blades, due to manufacturing tolerances, deterioration over a lifetime, or blade repair, can influence overall aerodynamic performance as well as aeroelastic behaviour. In cooled turbine blades, such deviations may lead to streaks of high or low temperature. It has already been shown that hot streaks from the combustors lead to inhomogeneity in the flow path, resulting in increased blade dynamic stress. However, not only hot streaks but also cold streaks occur in modern aircraft engines due to deterioration-induced widening of cooling holes. This work investigates this effect in an experimental setup of a five-stage axial turbine. Cooling air is injected through the vane row of the fourth stage at midspan, and the vibration amplitudes of the blades in rotor stage five are measured with a tip-timing system. The highest injected mass flow rate is 2% of the total mass flow rate for a low-load operating point. The global turbine parameters change between the reference case without cooling air and the cold streak case. This change in operating conditions is compensated such that the corrected operating point is held constant throughout the measurements. It is shown that the cold streak is deflected in the direction of the hub and detected at 40% channel height behind the stator vane of the fifth stage. The averaged vibration amplitude over all blades increases by 20% for the cold streak case compared to the reference during low-load operating of the axial turbine. For operating points with higher loads, however, no increase in averaged vibration amplitude exceeding the measurement uncertainties is observed because the relative cooling mass flow rate is too low. It is shown that the cold streak only influences the pressure side and leads to a widening of the wake deficit. This is identified as the reason for the increased forcing on the blade. The conclusion is that an accurate prediction of the blade’s lifetime requires consideration of the cooling air within the design process and estimation of changes in cooling air mass flow rate throughout the blade’s lifetime.

KW - aerodynamics

KW - aeroelasticity

KW - axial turbines

KW - blade vibrations

KW - experimental investigations

KW - forced response

UR - http://www.scopus.com/inward/record.url?scp=85204933909&partnerID=8YFLogxK

U2 - 10.3390/ijtpp9030024

DO - 10.3390/ijtpp9030024

M3 - Article

AN - SCOPUS:85204933909

VL - 9

JO - International Journal of Turbomachinery, Propulsion and Power

JF - International Journal of Turbomachinery, Propulsion and Power

IS - 3

M1 - 24

ER -