Design and Simulation of Two Coupled High-Dynamic Axes with Linear Direct Drives and Linear Magnetic Guides

Publikation: Beitrag in Buch/Bericht/Sammelwerk/Konferenzband › Aufsatz in Konferenzband › Forschung › Peer-Review

Autorschaft

  • Hans Kurt Tönshoff
  • R. Kaak
  • Ch. Lapp
  • M. Ruskowski

Organisationseinheiten

Externe Organisationen

  • Laser Zentrum Hannover e.V. (LZH)
Forschungs-netzwerk anzeigen

Details

OriginalspracheEnglisch
Titel des SammelwerksProc. of the 2nd Int. Conference on High Speed Machining
ErscheinungsortDarmstadt, Germany
Seiten263-267
PublikationsstatusVeröffentlicht - 1999

Abstract

It could be shown that ADAMS is a powerful simulation tool to handle dynamic problems during the development phase of high speed machine tools. Furthermore it can be stated that it takes a huge time effort for the development engineer if there exist various construction parameters. For this reason a especially adjusted software was self-developed. Concerning the prototype construction it must be confessed that the simulation results reveal deviations to an extent that would make this structural component useless for the application in high speed machine tools. But, the control concept is not as sophisticated modeled as it is in reality and moreover the simulation was carried out with time steps of 0.005 s which corresponds to a frequency of 200 Hz. In reality a sampling frequency of 20 kHz will be used what divides the length of the time steps by 100. Thus, deviations will be detected earlier so that reactions also can take place much earlier.

Zitieren

Design and Simulation of Two Coupled High-Dynamic Axes with Linear Direct Drives and Linear Magnetic Guides. / Tönshoff, Hans Kurt; Kaak, R.; Lapp, Ch. et al.
Proc. of the 2nd Int. Conference on High Speed Machining. Darmstadt, Germany, 1999. S. 263-267.

Publikation: Beitrag in Buch/Bericht/Sammelwerk/Konferenzband › Aufsatz in Konferenzband › Forschung › Peer-Review

Tönshoff, HK, Kaak, R, Lapp, C & Ruskowski, M 1999, Design and Simulation of Two Coupled High-Dynamic Axes with Linear Direct Drives and Linear Magnetic Guides. in Proc. of the 2nd Int. Conference on High Speed Machining. Darmstadt, Germany, S. 263-267.
Tönshoff, H. K., Kaak, R., Lapp, C., & Ruskowski, M. (1999). Design and Simulation of Two Coupled High-Dynamic Axes with Linear Direct Drives and Linear Magnetic Guides. In Proc. of the 2nd Int. Conference on High Speed Machining (S. 263-267).
Tönshoff HK, Kaak R, Lapp C, Ruskowski M. Design and Simulation of Two Coupled High-Dynamic Axes with Linear Direct Drives and Linear Magnetic Guides. in Proc. of the 2nd Int. Conference on High Speed Machining. Darmstadt, Germany. 1999. S. 263-267
Tönshoff, Hans Kurt ; Kaak, R. ; Lapp, Ch. et al. / Design and Simulation of Two Coupled High-Dynamic Axes with Linear Direct Drives and Linear Magnetic Guides. Proc. of the 2nd Int. Conference on High Speed Machining. Darmstadt, Germany, 1999. S. 263-267
Download
@inproceedings{874fe0b16f624713b0e9824828f501ae,
title = "Design and Simulation of Two Coupled High-Dynamic Axes with Linear Direct Drives and Linear Magnetic Guides",
abstract = "It could be shown that ADAMS is a powerful simulation tool to handle dynamic problems during the development phase of high speed machine tools. Furthermore it can be stated that it takes a huge time effort for the development engineer if there exist various construction parameters. For this reason a especially adjusted software was self-developed. Concerning the prototype construction it must be confessed that the simulation results reveal deviations to an extent that would make this structural component useless for the application in high speed machine tools. But, the control concept is not as sophisticated modeled as it is in reality and moreover the simulation was carried out with time steps of 0.005 s which corresponds to a frequency of 200 Hz. In reality a sampling frequency of 20 kHz will be used what divides the length of the time steps by 100. Thus, deviations will be detected earlier so that reactions also can take place much earlier. ",
author = "T{\"o}nshoff, {Hans Kurt} and R. Kaak and Ch. Lapp and M. Ruskowski",
year = "1999",
language = "English",
pages = "263--267",
booktitle = "Proc. of the 2nd Int. Conference on High Speed Machining",

}

Download

TY - GEN

T1 - Design and Simulation of Two Coupled High-Dynamic Axes with Linear Direct Drives and Linear Magnetic Guides

AU - Tönshoff, Hans Kurt

AU - Kaak, R.

AU - Lapp, Ch.

AU - Ruskowski, M.

PY - 1999

Y1 - 1999

N2 - It could be shown that ADAMS is a powerful simulation tool to handle dynamic problems during the development phase of high speed machine tools. Furthermore it can be stated that it takes a huge time effort for the development engineer if there exist various construction parameters. For this reason a especially adjusted software was self-developed. Concerning the prototype construction it must be confessed that the simulation results reveal deviations to an extent that would make this structural component useless for the application in high speed machine tools. But, the control concept is not as sophisticated modeled as it is in reality and moreover the simulation was carried out with time steps of 0.005 s which corresponds to a frequency of 200 Hz. In reality a sampling frequency of 20 kHz will be used what divides the length of the time steps by 100. Thus, deviations will be detected earlier so that reactions also can take place much earlier.

AB - It could be shown that ADAMS is a powerful simulation tool to handle dynamic problems during the development phase of high speed machine tools. Furthermore it can be stated that it takes a huge time effort for the development engineer if there exist various construction parameters. For this reason a especially adjusted software was self-developed. Concerning the prototype construction it must be confessed that the simulation results reveal deviations to an extent that would make this structural component useless for the application in high speed machine tools. But, the control concept is not as sophisticated modeled as it is in reality and moreover the simulation was carried out with time steps of 0.005 s which corresponds to a frequency of 200 Hz. In reality a sampling frequency of 20 kHz will be used what divides the length of the time steps by 100. Thus, deviations will be detected earlier so that reactions also can take place much earlier.

M3 - Conference contribution

SP - 263

EP - 267

BT - Proc. of the 2nd Int. Conference on High Speed Machining

CY - Darmstadt, Germany

ER -