Details
| Originalsprache | Englisch |
|---|---|
| Seiten (von - bis) | 732-737 |
| Seitenumfang | 6 |
| Fachzeitschrift | Procedia CIRP |
| Jahrgang | 116 |
| Publikationsstatus | Veröffentlicht - 2023 |
| Veranstaltung | 30th CIRP Life Cycle Engineering Conference, LCE 2023 - New Brunswick, USA / Vereinigte Staaten Dauer: 15 Mai 2023 → 17 Mai 2023 |
Abstract
A significant percentage of energy in hot forming is used to heat the components. Especially in manufacturing hybrid components, workpieces are heated in the preceding hot-joining process in addition to the heating cycles. Nevertheless, previous processing steps require longer times than the following hot forming processes leading to long downtimes. With the pre-production of workpieces, the machine's capacity is fully utilized but prevents the reuse of the residual heat. Consequently, an immense amount of energy is wasted due to additionally required heating cycles. Our approach is to develop a flexible and resource-efficient process chain. We combine two hot forming processes with different cycle times in a single process chain. Therefore, we consider the process of a hybrid bevel gear with heat and time-consuming preparation and a hybrid shaft with moderate preparation effort. To compensate for the bevel gear's high cycle times, the shaft is hot-formed during the downtimes. In order to reuse the residual heat of the bevel gear, their hot-forming process run is prioritized: Whenever the bevel gear's workpiece is manufactured, it will be hot-formed immediately. Combining these process chains allows the forming machine's capacity to be fully utilized and energy utilization optimized.
ASJC Scopus Sachgebiete
- Ingenieurwesen (insg.)
- Steuerungs- und Systemtechnik
- Ingenieurwesen (insg.)
- Wirtschaftsingenieurwesen und Fertigungstechnik
Zitieren
- Standard
- Harvard
- Apa
- Vancouver
- BibTex
- RIS
in: Procedia CIRP, Jahrgang 116, 2023, S. 732-737.
Publikation: Beitrag in Fachzeitschrift › Konferenzaufsatz in Fachzeitschrift › Forschung › Peer-Review
}
TY - JOUR
T1 - Concept for a resource-efficient process chain for hybrid bulk components with optimized energy utilization
AU - Ince, C. V.
AU - Blümel, R.
AU - Raatz, A.
N1 - Funding Information: The results presented in this paper were obtained within the Collaborative Research Centre 1153 ’Process chain to produce hybrid high-performance components by Tailored Forming’ - 252662854 in subproject C07. The authors would like to thank the German Research Foundation (DFG) for the financial and organizational support of this project.
PY - 2023
Y1 - 2023
N2 - A significant percentage of energy in hot forming is used to heat the components. Especially in manufacturing hybrid components, workpieces are heated in the preceding hot-joining process in addition to the heating cycles. Nevertheless, previous processing steps require longer times than the following hot forming processes leading to long downtimes. With the pre-production of workpieces, the machine's capacity is fully utilized but prevents the reuse of the residual heat. Consequently, an immense amount of energy is wasted due to additionally required heating cycles. Our approach is to develop a flexible and resource-efficient process chain. We combine two hot forming processes with different cycle times in a single process chain. Therefore, we consider the process of a hybrid bevel gear with heat and time-consuming preparation and a hybrid shaft with moderate preparation effort. To compensate for the bevel gear's high cycle times, the shaft is hot-formed during the downtimes. In order to reuse the residual heat of the bevel gear, their hot-forming process run is prioritized: Whenever the bevel gear's workpiece is manufactured, it will be hot-formed immediately. Combining these process chains allows the forming machine's capacity to be fully utilized and energy utilization optimized.
AB - A significant percentage of energy in hot forming is used to heat the components. Especially in manufacturing hybrid components, workpieces are heated in the preceding hot-joining process in addition to the heating cycles. Nevertheless, previous processing steps require longer times than the following hot forming processes leading to long downtimes. With the pre-production of workpieces, the machine's capacity is fully utilized but prevents the reuse of the residual heat. Consequently, an immense amount of energy is wasted due to additionally required heating cycles. Our approach is to develop a flexible and resource-efficient process chain. We combine two hot forming processes with different cycle times in a single process chain. Therefore, we consider the process of a hybrid bevel gear with heat and time-consuming preparation and a hybrid shaft with moderate preparation effort. To compensate for the bevel gear's high cycle times, the shaft is hot-formed during the downtimes. In order to reuse the residual heat of the bevel gear, their hot-forming process run is prioritized: Whenever the bevel gear's workpiece is manufactured, it will be hot-formed immediately. Combining these process chains allows the forming machine's capacity to be fully utilized and energy utilization optimized.
KW - Hybrid Bulk Components
KW - Resource-Efficient
KW - Tailored-Forming-Process
UR - http://www.scopus.com/inward/record.url?scp=85164278262&partnerID=8YFLogxK
U2 - 10.1016/j.procir.2023.02.123
DO - 10.1016/j.procir.2023.02.123
M3 - Conference article
AN - SCOPUS:85164278262
VL - 116
SP - 732
EP - 737
JO - Procedia CIRP
JF - Procedia CIRP
SN - 2212-8271
T2 - 30th CIRP Life Cycle Engineering Conference, LCE 2023
Y2 - 15 May 2023 through 17 May 2023
ER -